Видео

I'm confused, what did you do to repair it.

Подскажите маркировку пожалуйста тех двух транзисторов

Good job ❤

Hi, I have skoda fabia 1.4d 2016. Seems with same problem. Can I take off this unit and send over to you via post for repair? M

Why not use spot welder could be easier?

What do you use for soldering material? Argento? Or alluminio?

Which one of the components on the board is the eeprom? Location?

Hello master, I watched some of your videos, based on this video alone. I also calibrated the faulty km and rpm hands by doing a needle calibration test with MDI, by doing the same as you in the test mode. I went to a distance of 450 km outside the city, and 20 km after I set off, when I stopped at the traffic light, the speedometer needle was stopped. I noticed that it stopped at 10 km. When I reached my destination, this time when I stopped, I noticed that the rev needle was showing more than normal. When I turned off the ignition, both needles were not at the zero point, but slightly above. After returning home, I checked it after resetting the needles by manually adjusting it manually, not with the device, by removing and plugging the rear socket of the indicator. and there is no problem now. I think that the extra settings made to the indicator later do not give healthy results.

hi! How can I contact you? need help with repairing this.

F0

Perfect

Perfect

Perdeci jop 👏 Where can I find the ecu circuit diagram?

Great work engineer!!

شكرا جزيلا لك مهندس ..

Can you imagine if they engineered airplanes so that if an instrument goes bad the engines shut down and you can't restart them😢

Do yoy know what code does this problem send? I have P2149 code , and im suspect about this

Great as this is, there's an underlying issue - a bit of the motherboard has failed. Right, so you can swap the eprom into another used motherboard & away you go - however that presents the issue of dickery & having to find a used good unit.. A better question would be, what bit of the original motherboard has failed & how can that failure be repaired. With all due respect.

Please i need a same chip. Where can I find this? Thanks

what is the gel like substance that is on the board?

Ford Trucks samtech fiyatı nedir

A wise man said "use Kapton tape every time you have plastic connectors besides"...

I think that you better not do this job and replace the board if you have this board as new or fixed

Ooh. It's just a Mosfet. So, three contacts to solder basically. Nice.

Haven't got time to watch all this but wondered if you checked the caps around the cooked ICs. Nice job otherwise. Thanks for posting.

Hi ! Can you tell me the internet site for to buy this chip please. Thank you very much 🙏

Good work

Hi what temperature u use it

You don't need to replace all injectors surely??

He is did format and after install to the car programming by scanner again

Interesting that airbag light does not come on but it brings down communication when installed. Have you tried connecting with just it while on bench?

Twist the wires together, then slide over the twisted wires! Makes a way stronger connection!

What is the resistance between CAN H and CAN L?

HI! The dealer should have offered the new module. To program after installation. This is a proper dealer repair procedure. He can guarantee this, this work is guaranteed! It is a waste of money to inspect the control unit of a safety equipment, because it may not be repairable. Repair is risky. Even with that, the new one and the repair will be more expensive.

What temperature are you using for solder tip and fan?

@urigenvan hace 9 minutos Hello, can I write to you by email or could you watch this video of the bcm of my 2007 Ford Transit to see if this diode is missing or is it like that???, it is only a minute of video, to clear up doubts, I would also like to know How do I know what each relay corresponds to since when the lights of the flashing warnings stayed on I heard how a relay was activated as if it were stuck or hooked, strange noises in the relays, thank you very much

❤❤

Hi how did this error show up? I Have problem with battery charging, charging is Ok 14,2V but battery still flashing on dash, new alternator, LIN Ok

Cpu problem what coding used

Very nice but there is an easier way..I used CH341A programmer with free software to read the eprom in the radio. I got the tip from Norfo garage here on youtube

Good work ❤

Where the link for tools shop?

how much hot to set and the blow air??

Sorry! your store is dead?

Is bro restarted?

Great

Same problem

Hello I have radio from bmw I need to read eprom you know how to do

It work for Alfa Romeo Giulia BCM?